rob.a.dunbar
Posts: 19
Joined: Thu Jan 30, 2014 2:56 am

Installer Crashes and unable to close

This is using 10.9 and is similar to http://www.advancedinstaller.com/forums ... =2&t=27916 and unfortunately I don't have a "clean" machine to test on, but a number of our users have run into this issue.

The most recent change I made was to enable the Enhanced Installer option. That said, I have re-run my installer several times and can't reproduce the issue. When received it the first time, I had just finished installing and then proceeded to perform an uninstall, it appeared to lock up during "calculating disk space" and then the it crashed. Followed by any time cancel or 'X' to close the installer I would receive the second error. And had to call Task Manager's End Process.


[SEH_AV_DEP_BADPTR] ACCESS_VIOLATION (0xc0000005) at address [0x00fd14e9]
*** Stack Trace (x86) ***
[0x00fd14e9] -----
[0x7201803c] MsiSetOfflineContextW()
[0x71eda584] MsiInvalidateFeatureCache()
[0x71f35d12] MsiGetPropertyW()
[0x0044425f] -----
[0x004587ff] -----
[0x00460d4a] -----
[0x00460848] -----
[0x0045abd0] -----
[0x0045466c] -----
[0x0045a52f] -----
[0x0045a4fa] -----
[0x0045896e] -----
[0x0045a202] -----
[0x003fcf29] -----
[0x003fd161] -----
[0x003fd8ed] -----
[0x0040cee2] -----
[0x777d9f72] RtlInitializeExceptionChain()
[0x777d9f45] RtlInitializeExceptionChain()
[0x003b0000] MODULE_BASE_ADDRESS


After the cancel is clicked
[SEH_AV_READ_BADPTR] ACCESS_VIOLATION (0xc0000005) at address [0x004419c4]
*** Stack Trace (x86) ***
[0x004419c4] -----
[0x037cfcb8] -----
[0x76831e4b] GetProcAddress()
[0x00469432] -----
[0x004694a8] -----
[0x0040cee2] -----
[0x777d9f72] RtlInitializeExceptionChain()
[0x777d9f45] RtlInitializeExceptionChain()
[0x003b0000] MODULE_BASE_ADDRESS
rob.a.dunbar
Posts: 19
Joined: Thu Jan 30, 2014 2:56 am

Re: Installer Crashes and unable to close

On another users PC it just happened again, they uninstalled a previous build (.130) of the installer, and then ran the newer build (.139) and received the same problem.
Daniel
Posts: 8283
Joined: Mon Apr 02, 2012 1:11 pm
Contact: Website

Re: Installer Crashes and unable to close

Hello,

I'm not sure why this happens. Can you please send us the .aip (project file) to support at advancedinstaller dot com so we can investigate? Also, if you have generated a verbose log for a failing installation please send it us too.

It would be useful if you could isolate the behavior in a buildable sample and send it us alongside a test case scenario so we can test and investigate this. Also, please specify what is the target machine software configuration (Windows version, SP level, OS language, etc.) where the related error appears.

All the best,
Daniel
Daniel Radu - Advanced Installer Team
Follow us: Twitter - Facebook - YouTube
rob.a.dunbar
Posts: 19
Joined: Thu Jan 30, 2014 2:56 am

Re: Installer Crashes and unable to close

I've sent an email with the .aip file. Unfortunately we haven’t been able to isolate the error, its sporadic.... One user experienced three times in two days, so its a major problem.
I’m running Windows 7 Pro 64 bit, SP1, but I all the other testers are also running windows 7 pro with sp1, but likely to be 32 and 64.

It’s been very noticeable after enabling the Enhance User Interface feature. I'm unsure if the problem existed before hand, but since making that single change last week, I've been receiving complaints. With that in mind I'm going to disable that feature as we're putting out a release on Friday.
rob.a.dunbar
Posts: 19
Joined: Thu Jan 30, 2014 2:56 am

Re: Installer Crashes and unable to close

I spotted the Enable Verbose Logging in the Install Parameters. Unfortunately we're sending out a release tomorrow, but after that I'll put it back while testing in house.
rob.a.dunbar
Posts: 19
Joined: Thu Jan 30, 2014 2:56 am

Re: Installer Crashes and unable to close

Just to note, that I received a similar exception on a brand new (one file) installer using 11.2 on a separate machine. The Enhance UI option was enabled.
After rebuilding and running again, it worked. As a result of this intermittent behavior, I have recommended that my team always disable the Enhanced UI option for any further installers.
JustAProgrammer
Posts: 26
Joined: Mon Apr 07, 2014 10:11 pm

Re: Installer Crashes and unable to close

We are seeing a similar issue that is sporadic as well, it is interesting to see it seems to be something with the Enhanced UI. Unfortunately we cannot disable the Enhanced UI due to needing to use the bootstrapper if some pre-reqs are not there.

Has there been any progress made on this or ideas?
Daniel
Posts: 8283
Joined: Mon Apr 02, 2012 1:11 pm
Contact: Website

Re: Installer Crashes and unable to close

Hello,

Unfortunately, we cannot add add a fix to this stochastic issue as long as we aren't able to isolate and replicate it on our test machines. In order to be able to fix this issue we need to replicate it on our side. So, it would be useful if you could isolate this in a sample and send it us to support at advancedinstaller dot com so we can investigate.

Until now, this issue seems to be caused by our "Enhanced User Interface" feature. As a workaround, you can set the "Classic" theme as your current theme and disable the "Enhanced User Interface" feature. Please note that you can still build an EXE setup package type, even when the "Enhanced User Interface" feature is disabled.

All the best,
Daniel
Daniel Radu - Advanced Installer Team
Follow us: Twitter - Facebook - YouTube

Return to “Common Problems”